Shop headings: New Spares | Used Spares | Accessories | Brands
Sidestand cutout switch
See ELA81319 for rotary switch that was fitted to some models
This part is available by special order, request a quote
639542 MG639542
£28.00
INC VAT
£23.33 EX VAT
Oil pressure switch
Does not fit models with 2 valves per cylinder. See ENA12640 for replacement crush washer if required.
Discontinued by Guzzi in 2014, superceded by ELA32710, note ELA32710 has a single male spade connector so it will be necessary to modify wiring to connect this switch
Sorry, this part is no longer available.
978854 MG978854
Sorry this item is out of production
Chrome finish plastic horn cover
Sorry, this part is no longer available.
31744765 GU31744765 31 74 47 65
3174 4765 3174.4765 31.74.47.65
Sorry this item is out of production
Mechanical Bosch voltage regulator
- Nominal current: 25 amps - Nominal voltage: 14V - Length: 120 mm - Width: 70 mm - Height: 80 mm
This part is available by special order, request a quote
12703805-z 12703805 GU12703805 12 70 38 05
1270 3805 1270.3805 12.70.38.05
£165.00
INC VAT
£137.50 EX VAT
Dizzie rotor arm
This part is due back in stock soon, call 01484 841395 to reserve yours
12715431 GU12715431 12 71 54 31
1271 5431 1271.5431 12.71.54.31
£12.50
INC VAT
£10.42 EX VAT
Complete electronic ignition kit containing alternator mounted ignition pickup, fittings and amplifier unit. Works with 12 volt 3 Ohm coils ELA14500 (big twins) and can be used to replace Digiplex on models with Ducati charging systems where the bike is converted to carburettors. This kit is just an ignition system, it will not control fuelling. The pickups for this kit are mounted on the alternator stator. Supplied with instructions in German with wiring diagrams.
2 year warranty on Sachse ignition kits
Once fitted no further adjustment should be necessary. Preloaded with nine ignition curves, two of which are designed for twin plugged bikes. See this link for fitting instructions. Some bikes may need at least one additional spacer to allow enough clearance for alternator cover to fit once pickup is fitted. Note that if you are replacing a Digiplex system you will also need to replace your 'square' coils with higher impedance 12 volt coils e.g. ELA14500
This part is available by special order, request a quote
£395.00
INC VAT
£329.17 EX VAT
Brand new right hand original "Lego" type switchgear and twistgrip with switches for starter and run/kill.
Previously unavailable new and ideal for your restoration project.
Comes with attached 4 pin molex connector, molex pins and rubber boot, ready to be plugged into your standard loom.
Twistgrip for standard dual throttle cables.
See ELA17061 and ELA14055 for left hand switches.
Sorry, this part is no longer available.
Sorry this item is out of production
Cut out switch, threaded body. Used as sidestand switch on big twins and clutch cut out switch on V7 series small twins and Breva 750
This part is available by special order, request a quote
29759150 GU29759150 29 75 91 50
2975 9150 2975.9150 29.75.91.50
£75.00
INC VAT
£62.50 EX VAT
Lambda sensor with 660mm lead
This part is available by special order, request a quote
896110 MG896110
£121.00
INC VAT
£100.83 EX VAT
Lambda sensor with 325mm lead
This part is available by special order, request a quote
584344 MG584344
£149.00
INC VAT
£124.17 EX VAT